manualshive.com logo in svg

IBM ThinkPad 380Z, User Manual

Share
Download
IBM ThinkPad 380Z User Manual Download Page 44

– Change the system configuration: You can change the

system configuration with your operating system or with the
ThinkPad Configuration program.

Note:

If the PC Card device driver is the PC Card point enabler,
you cannot use the PC Card with ThinkPad PC Card
support software. Check with the card vendor whether the
device driver is a client device driver or a point enabler.

 Power Management

Depending on the function of the PC Card, changing from one power
management mode to another might cause your ThinkPad computer
to hang. PC Card support software prevents this occurrence through
special handling during power state transition:

The following table approximately indicates the supported power
management function depending on the type of PC Card. Make sure
that your PC Card supports the function.

 
Card Type

Suspend Request (Fn

+

F4)

Hibernation Request (Fn

+

F12)

ac Power

Battery Power

ac Power

Battery Power

Modem or
Network

Supported

Supported

Not Supported

Supported

Other

Supported

Supported

Supported

Supported

Note:  Standby mode is always accepted.

For more information about the PC Card support software, go to the
appropriate section according to the following table:

Using a PC Card in Windows 95 (with CardWorks)

Using a PC Card in Windows NT (with CardWizard)

Using a PC Card in Windows 3.1 (with CardWizard)

Using a PC Card in OS/2 (with PC Card Director)

Using a PC Card in DOS (with CardSoft)

40

IBM ThinkPad 380Z Online User's Guide 

 

Summary of Contents for ThinkPad 380Z






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands