IBM ThinkPad 380Z User Manual Download Page 139

Page: 139 / 157

Appendix A. Using PS2 Commands

Using PS2 Command

This section describes PS commands in general. Depending on the
features of your computer, some commands might not apply. Please
note that the

PS2

commands are subject to change without notice. If

you enter a command written in this section and receive an error,
type

PS2 ?

and refer to the online help menu.

You can enter the following

PS2

command options from the DOS and

DOS command prompts on Windows 3.1, Windows NT, Windows 95,
Windows 98, and OS/2. to set the features for your computer.
When entering a command, enter it in the following syntax:

PS2

[

Parameter1] [Parameter2] [Parameter3]

Note:

The following PS2 commands do not supported by Windows
98.

PRESENtation

HTimer

POwer

DSIK

LCd

TImer

DEFAULT

Syntax Rules

Refer to these notes when you enter a command.

135

Summary of Contents for ThinkPad 380Z






























































































































































Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands

IBM ThinkPad 380Z, User Manual

Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands