IBM ThinkPad 380Z User Manual Download Page 108

Page: 108 / 157

Press OK in the “CrystalWare Configuration” panel. When the
installation program prompts you, restart Windows NT to make
the change effective.

Installing the IBM TrackPoint Driver for Windows NT

The TrackPoint Driver Diskette II for Win95/98/NT is intended for use
with the IBM PS/2 TrackPoint Version 4.0 or later.

To install the TrackPoint driver for Windows NT:

Start Windows NT.

Insert the TrackPoint Driver Diskette II for Win95/98/NT into the
diskette drive.

Click on Start.

Move the cursor to Settings; then click on Control Panel.

Double-click on the Mouse icon.

Click on the General tab at the top of the “Mouse Properties”
window.

Click on Change.

Click on Have Disk.

Click on OK.

Click on PS/2 TrackPoint in the list.

Click on OK.

Click on Close in the “Mouse Properties” window.

Remove the TrackPoint Driver Diskette II for Win95/98/NT from
the diskette drive, and restart your computer to make the new
settings effective.

Installing the Infrared Device Driver for Windows NT

You can use infrared features using Windows NT dial-up networking.
The Windows NT infrared device driver provides you IrDA 1.0

104

IBM ThinkPad 380Z Online User's Guide

Summary of Contents for ThinkPad 380Z






























































































































































Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands

IBM ThinkPad 380Z, User Manual

Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands