IBM ThinkPad 380Z User Manual Download Page 140

Page: 140 / 157

Syntax

Rule

Select one of the options on either side of the
vertical bar ( | ).

Highlighted

Enter the exact highlighted letters in either
uppercase or lowercase.

UPPERCASE

Enter any value within the specified range for
the following:

0–20

0–23

0–59

Note:

The

(minutes) and

(seconds)

parameters are optional. The default
values are 0.

lowercase

Command elements in lowercase are optional.
For example, entering

PS2 SE OF

and

PS2

SErial OFf

gives the same results.

PS2 Command

The following is a list of commonly used

PS2

commands. The

description have the following format:

Description of the command

—Or—

Parameter1

Parameter2

Parameter3

Parameter1

Parameter2

Parameter3

Parameter4

Alarm (Sound) Command

Set the computer to beep in certain conditions:

BEEP

ON | OFf

Alarm | System | Warn

136

IBM ThinkPad 380Z Online User's Guide

Summary of Contents for ThinkPad 380Z






























































































































































Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands

IBM ThinkPad 380Z, User Manual

Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands