IBM ThinkPad 380Z User Manual Download

Page: 142 / 157

Display the DMA channel assignments:

FDD

External | Internal

—

? DMA

—

CPU Speed

Set the processor speed:

: Specifies CPU speed when the AC Adapter is connected.

: Specifies CPU speed when using battery power.

Note:

If the

option is not specified, this command is

effective on the current power management mode set by
the

commands.

SPeed

Fixed | Auto

MAX | Medium | Slow

[AC | DC]

Display Commands

Set the screen expansion:

Disable the screen blanking function, and the standby and

suspend timers:

Set the brightness control of the LCD:

Set where to display information:

HVEXPansion

ON | OFf

—

PRESENtation

Enable | Disable

—

BRightness

High | Normal

—

SCreen

LCD | CRT | BOTH

—

138

IBM ThinkPad 380Z Online User's Guide

Summary of Contents for ThinkPad 380Z






























































































































































Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands

IBM ThinkPad 380Z, User Manual

Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands