IBM Aptiva 2124 Hardware Maintenance Service Download Page 185

Page: 185 / 310

5-22

3.5-In. Hard Disk Drive Jumper Settings

The configuration of the following jumpers controls the drive’s mode of
operation:

•

SP – Slave Present

•

DS – Drive Select

•

CS – Cable Select

•

PK – Park, used as a place to store a jumper

Seagate Hard Disk Drive

Table 5-13

Seagate Hard Disk Drive Jumper Settings

CS/SP

Description

Off

Drive configured as a Master.

Off

Drive configured as a Slave.

Drive configured as a Master, with an attached Slave

Maxtor Hard Disk Drive

Table 5-14

Maxtor Hard Disk Drive Jumper Settings

J50:Master/Slave

Description

Only drive in single drive system, or
Master drive in dual drive system

Off

Slave drive in dual drive system

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands