IBM Aptiva 2124 Hardware Maintenance Service Download Page 183

Page: 183 / 310

5-20

3.5-In. Hard Disk Drive Jumper Settings

The configuration of the following jumpers controls the drive’s mode of
operation:

•

SP – Slave Present

•

DS – Drive Select

•

CS – Cable Select

•

PK – Park, used as a place to store a jumper

Quantum Fireball TM and ST Series Hard Disk Drives

Table 5-10

Quantum Fireball TM and ST Series Hard Disk Drives Jumper
Settings

Description

Off

Drive configured as a Master, or
Drive configured as a Master, with an attached Slave

Off

Drive configured as a Slave.

Seagate Hard Disk Drive

Table 5-11

Seagate Hard Disk Drive Jumper Settings

CS/SP

Description

Off

Drive configured as a Master.

Off

Drive configured as a Slave.

Drive configured as a Master, with an attached Slave

Maxtor Hard Disk Drive

Table 5-12

Maxtor Hard Disk Drive Jumper Settings

J50:Master/Slave

Description

Drive configured as a Master, or
Drive configured as a Master, with an attached Slave

Off

Drive configured as a Slave.

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands