IBM Aptiva 2124 Hardware Maintenance Service Download Page 169

Page: 169 / 310

5-6

2153/K6 Processor Type Jumper Settings

WARNING: You must verify the exact processor type before setting the

processor type jumpers. The wrong processor type jumper setting
may damage the CPU. The system only supports dual-voltage CPU.

Table 5- 2

Machine Type 2153 Processor Type Jumper Settings

CPU

SW1

SW2

SW3

JPX1

K6-2
266
66MHz

F N F N F N F F F N F N F F 2-3

K6S
300
66MHz

F N F N N N F F F N F N F F 1-2

K6-2
300
66MHz

F N F N N N F F F N F N F F 2-3

K6-2
300
100MHz

N F F F N F F F F N F N N N 2-3

K6-2
333
95MHz

F F F F F F F F F N F N N F 2-3

K6-2
350
100MHz

N F F F F F F F F N F N N N 2-3

N-On, F-Off

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands