IBM Aptiva 2124 Hardware Maintenance Service Download Page 186

Page: 186 / 310

Parts/Test Point Locations 5-23

5.25-In Hard Disk Drive Jumper Locations (For
2153)

Figure 5- 14 5.25-in Hard Disk Jumper Locations

The configuration of the following four jumpers controls the drive’s mode of
operation:

•

DS – Drive Select

•

CS/ SP–Cable Select / Slave Present

•

PARK – Used as a place to store a jumper

5.25-In Hard Disk Drive Jumper Settings

Table 5-15

5.25-in Hard Disk Drive Jumper Settings

CS/SP

Description

Off

Drive configured as a Master.

Off

Drive configured as a Slave.

Drive configured as a Master, with an attached Slave

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands