IBM Aptiva 2124 Hardware Maintenance Service Download Page 153

Page: 153 / 310

Repair Information 4-41

Pentium II Processor Module

Follow these steps to remove the Pentium II CPU module from the slot.
NOTE: Determine the type of processor you are installing and make sure the

jumpers are set correctly. Run the Setup Utility after correctly
installing a processor.

ATTENTION: Processors are sensitive to static discharge.

•

Unlock the latches that secure the processor module.

Figure 4- 38 Unlocking the Module Latches

•

Firmly hold the processor module and pull it out of the socket.

Figure 4- 39 Removing the Pentium II Processor

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands