IBM Aptiva 2124 Hardware Maintenance Service Download Page 93

Page: 93 / 310

Check Procedures 2-29

2. Select the Start icon.

3. Select Program, then select Accessories, Hyper Terminal.

4. Select an on-line service station, dial and connect to it.

004 - CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS

SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.)

−

The modem adapter functions normally.

−

End.

005 -

−

Ensure that Windows 98 is properly installed, then power off the
system unit.

−

Plug the modem adapter card into a different ISA expansion slot.

−

Go to step 002.

−

If the error symptom still remains, replace the modem adapter card.

−

End.

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands