IBM Aptiva 2124 Hardware Maintenance Service Download Page 140 | Manualshive

Page: 140 / 310

background image

4-28

2. Expansion slots.

On the rear panel of the system chassis are seven slot openings for
installation of adapter cards. When installing an adapter, remove the
cover of the slot that you intend to use.

3. Modem Card.

The system includes a 56.6K voice fax modem.

4. System board.

The system board is secured by screws on the inner wall of the chassis.

5. Bay 1.

This drive bay may accommodate a 5.25-inch half-high drive, such as
diskette, hard disk, tape, or CD/DVD-ROM drive. Normally, this bay holds
the factory-installed CD/DVD-ROM drive.

6. Bay 2.

This drive bay may accommodate a 5.25-inch half-high drive, such as
diskette, hard disk, tape or CD/DVD-ROM drive.

7. Bay 3.

This drive bay may accommodate a 5.25-inch half-high drive, such as
diskette, hard disk, tape or CD/DVD-ROM drive.

8. Bay 4.

This drive bay may accommodate a 3.5-inch slim drive, such as a diskette,
hard disk or tape drive. Normally, this bay holds a factory-installed
diskette drive.

9. Bay 5.

This drive bay may accommodate an internal 3.5-inch slim drive, such as a
hard disk drive.

«
...
138
139
140
141
142
...
»

Summary of Contents for Aptiva 2124























































































































































































































































































































Reviews:

No comments

Related manuals for Aptiva 2124

PlasmaSync 42VR5

Brand: NEC Pages: 11

Brand: NAiS Pages: 108

YUR.VISION YV24WBH1 -

Brand: YURAKU Pages: 2

YUR.VISION YV216WB2

Brand: YURAKU Pages: 11

YUR.VISION YV19WB1 -

Brand: YURAKU Pages: 2

Brand: Hanns.G Pages: 25

Brand: Eizo Pages: 4

Brand: Lanaform Pages: 312

Brand: OSEE Pages: 35

Brand: V7 Pages: 1

Reference Premiere RP-160M

Brand: Klipsch Pages: 68

Brand: max mobility Pages: 12

Brand: B&G Pages: 30

Brand: Sportline Pages: 13

Brand: Ikan Pages: 6

PDK 111C-0WG13L

Brand: IEE Pages: 8

Brand: Samsung Pages: 65

Brand: Samsung Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands