IBM Aptiva 2124 Hardware Maintenance Service Download Page 141 | Manualshive

Page: 141 / 310

background image

Repair Information 4-29

Cover

•

Disconnect the system unit power cord.

•

Release the lock that secures the cover at the back of the unit by pressing
it toward the unlocked icon.

•

Slip your hand into the underside of the front panel and pull the release
handle forward to release the cover.

•

The cover slides along grooves that run on the sides of the unit. While
still holding the handle, slide the cover forward to remove it completely.

•

Touch the bare metal frame of the system to dissipate any static electricity
from your body (do not touch any of the components inside the frame until
you have done this). Do not touch any component(s) with a voltage
warning label.

Figure 4- 27 Pulling out the cover

«
...
139
140
141
142
143
...
»

Summary of Contents for Aptiva 2124























































































































































































































































































































Reviews:

No comments

Related manuals for Aptiva 2124

Brand: GE Pages: 24

Corometrics 250cx Series

Brand: GE Pages: 250

Brand: Wacom Pages: 26

Brand: Panasonic Pages: 24

Viera TH-42PHD5

Brand: Panasonic Pages: 40

Toughbook CF-VDW07

Brand: Panasonic Pages: 80

Brand: Acer Pages: 14

Brand: Trane Pages: 68

Brand: I-Inc Pages: 19

Brand: OBH Nordica Pages: 60

Brand: Farenheit Pages: 4

Brand: DMHC Pages: 5

Brand: Van Mechelen Pages: 19

Brand: IBM Pages: 24

Brand: B&W electronics Pages: 4

ProLite T2234MSC

Brand: Iiyama Pages: 31

Brand: Xenarc Pages: 19

Brand: Hanns.G Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands