IBM Aptiva 2124 Hardware Maintenance Service Download Page 139 | Manualshive

Page: 139 / 310

background image

Repair Information 4-27

Identifying the Parts of the System Unit

Figure 4- 26 The parts of the system unit

This computer system has five bays that can hold up to three 5.25-inch and
two 3.5-inch drives. Additional devices can be installed in the empty bays.
Diskette drives in this unit use the standard diskette advanced technology
(ATX) interface. Hard disk drives in this unit use an Integrated Drive
Electronics (IDE) ATX interface. This computer supports the American
National Standards Institute (ANSI) standard for ATX attachment disk drives.

It also has interface slots for installation of additional card devices. Industry
standard architecture (ISA) and Peripheral Component Interconnect (PCI)
adapter cards are both supported.
1. Switching Power Supply.

The system comes with a 145-watt switching power supply.

«
...
137
138
139
140
141
...
»

Summary of Contents for Aptiva 2124























































































































































































































































































































Reviews:

No comments

Related manuals for Aptiva 2124

Brand: Daewoo Pages: 19

Brand: Daewoo Pages: 12

Brand: Daewoo Pages: 36

Brand: Daewoo Pages: 70

Brand: F&V Pages: 20

Brand: Displays2go Pages: 23

InView 2706-PENETx2-SC

Brand: Spectrum Controls Pages: 8

Brand: Marshall Electronics Pages: 2

Brand: Mastervolt Pages: 33

Brand: Kodak Pages: 28

Brand: Tyco Electronics Pages: 33

Brand: ViewSonic Pages: 18

Brand: G-STORY Pages: 35

Brand: Uniden Pages: 32

Brand: PYLE Audio Pages: 16

DoubleSight DS DS-1900 DS-1900

Brand: DoubleSight Pages: 2

Brand: Power Acoustik Pages: 5

Brand: Zenith Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands