IBM Aptiva 2124 Hardware Maintenance Service Download Page 192

Page: 192 / 310

Parts/Test Point Locations 5-29

DVD-ROM Drive Rear Panel Connectors and Features

Figure 5- 20 DVD-ROM Rear Panel

Table 5- 22

DVD-ROM Drive Rear Panel Connectors and Features

Item

Function

Connect to…

Power connector

Power supply

IDE Interface connector

System board (CN13)

Device Configuration jumper. See
Table 5-20.

Analogue Audio connector

System board (CN9)

DVD-ROM Drive Jumper Settings

Table 5-23

DVD-ROM Drive Jumper Settings

Description

Drive configured as a Master
(default).

Drive configured as a Slave.

Cable select

Summary of Contents for Aptiva 2124























































































































































































































































































































Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands

IBM Aptiva 2124, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2124

Reviews:

Related manuals for Aptiva 2124

Brands by name

Popular brands