PCNTNW-NW-074 The hardware interrupt cannot be set.
Explanation: An attempt was made to initialize a given hardware interrupt.
The attempt was not successful.
Action: Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page 30).
Make sure that the interrupt request numbers are set correctly. If you are
using an ISA adapter, make sure resources are reserved as ISA Legacy in the
Configuration/Setup utility programs (see “Plug and Play” on page 31.)
PCNTNW-NW-075 The Multiple Link Interface Driver (MLID) cannot be
registered with the Link Support Layer (LSL).
Explanation: An error occurred while the driver was trying to register with the
LSL.
Action: Check the version of the NetWare or IntraNetWare Operating
System. Make sure that this driver is correct for the version of NetWare or
IntraNetWare that you are using. Restart the server.
PCNTNW-NW-079 The Multiple Link Interface Driver (MLID) did not
initialize MSMTx Free Count.
Explanation: The MSMTx Free Count is not initialized correctly.
Action: Restart the server.
PCNTNW-NW-086 The driver parameter block is too small.
Explanation: The driver parameter block is too small.
Action: Restart the server.
PCNTNW-NW-087 The media parameter block is too small.
Explanation: The driver media parameter block is too small.
Action: Restart the server.
PCNTNW-NW-091 The hardware configuration conflicts.
Explanation: You tried to load a new frame type for the existing controller.
The hardware assumptions made in doing so are incorrect. This error can
also occur if you try to specify a mode (such as, redundancy) that conflicts
with another specified mode.
Action: Make sure that the hardware configuration matches the software
settings. See “PCI bus control” on page 30 for information on viewing and
changing interrupt requests.
PCNTNW-NW-126 The group bit in the node address override was
cleared.
Explanation: The IEEE address has a group bit indicating that an address
belongs to a group of stations. This bit is used only as a destination address;
it cannot be used as a source address. You tried to enter a source address
with this bit set. The driver cleared the group bit of the source address.
Action: None necessary, message is for information only.
PCNTNW-NW-127 The local bit in the node address override was set.
Explanation: The local bit in the IEEE address format indicates that the
addresses are being managed locally. If you use the node address override
capabilities of this driver to enter a new address, the local bit must be set.
You entered an address without the local bit set. The driver has set the local
bit.
Action: None necessary, message is for information only.
PCNTNW-NW-164 The device was not found.
Explanation: The driver cannot find an Ethernet controller in the server.
Action: Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page 30). If the Ethernet adapter is enabled, go to “Diagnostic test
programs” on page 10 to run the diagnostic utility.
Netfinity 5000 - Type 8659
35
Summary of Contents for 865951Y - Netfinity 5000 - 51Y
