manualshive.com logo in svg

i-CAT FLX, Installation Manual, Page: 68 / 106

Share
Download
i-CAT FLX Installation Manual Download Page 68

3-30

i-CAT FLX Installation Manual

032-0330-EN  Rev K 

Configure Legacy Practice Management Interface (Optional)

For sites that use a Practice Management system, configure the optional PM Interface software on the 
server. Refer to the 

i-CAT FLX User Manual 

for information about status messages that can be 

displayed.

NOTE: 

•

The Practice Management software should have been loaded during the installation of 
SmartScan STUDIO Server and Client components. Install it from the SmartScan STUDIO 
Server media and Client media if it is not installed.

•

Coordinate with the site PM system administrator for the options to be selected for the site. 

•

If the PM system and SmartScan STUDIO Integration Services are on different computers, 
coordinate with site IT to ensure that Windows share permissions allow file sharing between 
the computers. The PM.xml file must be accessible to SmartScan STUDIO and the PM 
system.

1.

On Control Panel, select SmartScan STUDIO Integration Services, then select 

PM Interface

 

tab.

2.

Enter or browse to the location of the PM.xml file. The PM.xml file is generated by the Patient 
Management system.

3.

In Advanced Cleanup Options (only one option is selectable at a time):

• Automatically Clean PM.xml File 

-

 

When selected, removes an exam from the PM.xml file 

after it is selected on the Scheduled Exam screen. Select this option only if the PM system 
does not perform cleanup itself. The PM system has to allow writing to the PM.xml file.

• Remove Orphaned Exams from PM.xml File

 - When selected (default), automatically 

removes completed exams from the PM.xml file after at least 30 days. Orphaned exams are 
completed, but contain no CT or PAN scans. This can happen when an exam is canceled or 
when only scouts are taken.

NOTE: 

If PM Exam Output is disabled, it is recommended that one of the Advanced Cleanup 

Options be selected.

Summary of Contents for FLX











































































































Reviews:

No comments