manualshive.com logo in svg

i-CAT FLX, Installation Manual, Page: 54 / 106

Share
Download
i-CAT FLX Installation Manual Download Page 54

3-16

i-CAT FLX Installation Manual

032-0330-EN  Rev K 

Scenario 4 - Upgrade Existing DEXIS (without i-CAT 17-19 or KaVo 3D eXam) with 

DEXIS - i-CAT FLX

1

Install i-CAT FLX (Chapters 1 and 2)

Scanner and controller installed and networked with IP address.  
SmartScan STUDIO is pre-installed at the factory.

2

Upgrade to DEXIS Core / DEXIS Eleven

Install and Configure DEXIS Core and Migrate Data:

DEXIS Eleven uses a different image database than previous versions of DEXIS. Using the 
DEXIS Core media, install DEXIS Core on the server that functions as the long-term data 
storage device and migrate existing patient data. Refer to the 

DEXIS Eleven Software Manual

 

for instructions.

Install DEXIS Eleven client software:

Using the DEXIS Eleven media, install DEXIS client software on all clinical workstations that are 
using DEXIS. DEXIS Eleven client software can also be installed on the server that functions as 
the long-term data storage device on a shared server-client.  Refer to the 

DEXIS Eleven 

Software Manual

 for instructions.

NOTE: 

Make sure there are no pending scans before beginning a DEXIS upgrade. Do not use 

DEXIS until the SmartScan STUDIO components are installed.

3

Install SmartScan STUDIO Server Components (page

 

3-17)

 on long-term storage server.

•

Integration Services (required by all sites)

•

PACS Storage Service (sites using PACS)

•

Data Utility (optional)

•

Patient Data Utility (optional)

•

Legacy Practice Management Interface (sites using PM system)

•

DEXIS

 

i-CAT FLX Server Plugin (required for all DEXIS sites)

NOTE: 

For a Shared Server - Client installation scenario, you must also load the DEXIS i-CAT 

FLX Client on the server (located on Client Components media). For a Separate Server - Client 
installation scenario, load the DEXIS i-CAT FLX Client component on the server only if the site 
plans to use the server as a client.

4

Install SmartScan STUDIO Client Components (page

 

3-21)

 

on workstations in front office, 

operatories, and consultation rooms.

•

SmartScan STUDIO Manager (required on one workstation for accessing QA test images)

•

PACS QR (sites using a PACS for image storage)

•

PACS MWL (sites using modality worklists for scheduling patients)

•

Legacy Practice Management Viewer Launcher (sites using PM system)

•

DEXIS i-CAT FLX Client (required for all DEXIS sites)

5

Install InVivoDental Software (page

 

3-24)

 as required.

If not already loaded, load on the workstation where the site will be viewing QA Tests.  
Load on workstations that will be using it to view patient images, as purchased by the site. 

NOTE: 

Vision is not supported on the i-CAT FLX, only TxSTUDIO and Dolphin viewers are 

supported.

Summary of Contents for FLX











































































































Reviews:

No comments