Husqvarna TC 250 2011 Page 48 Workshop Manual Download

Page: 48 / 366

D.18

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

Air filter check (TE - TXCi)

Turn the rear fixing (1) counter clockwise, remove it and extract the saddle releasing

it from the front retaining screw.

Take out the battery (A) and leave it hanging on the side of the motorcycle.

Remove the screw (3), remove the complete air filter (4) and separate filter (5) from

intake silencer (6).

Air filter cleaning

Wash the filter with a specific detergent (see "Capacities" table in Section A)

then dry it fully (wash filter with gasoline only in case of need). Plunge the filter

in special oil for filters (see "Capacities" table in Section A), then wring it to drain

superfluous oil.

Do not use fuel or a low flash-point solvent to clean the filtering element.

A fire or explosion could result.

Clean the filtering element in a well ventilated area and do not allow

sparks or flames anywhere near the working area.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands