Husqvarna TC 250 2011 Page 256 Workshop Manual Download

Page: 256 / 366

L.4

BRAKES

Ed. 07-2010

Brake disc

Checking the brake disc is an important safety procedure; the disc must be spot

less, i.e. free from corrosion, oil or other dirt or deep scoring.

Front brake disc diameter: 260 mm

Front brake disc thickness (when new): 3.0 mm

Wear limit: 2.5 mm

Rear brake disc diameter: 240 mm

Rear brake disc thickness (when new): 4.0 mm

Wear limit: 3.5 mm

Disc warpage must not exceed 0.15 mm (check disc mounted on the rim with

a dial gauge).

To remove the disc from the wheel rim, you need to loosen the four retaining

screws. On assembly, clean all mating surfaces thoroughly and tighten the screws

to the specified torque.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands