Husqvarna TC 250 2011 Page 105 Workshop Manual Download

Page: 105 / 366

F.13

ENGINE DISASSEMBLY

Ed. 07-2010

- Use a valve spring compressor to compress the valve springs. Be careful

not too damage the mating surfaces that contact the gasket or those of the

combustion chamber. Make sure the valve spring compressor is aligned

straight on the spring, or you might bend the valve stem. Do not compress

the springs too much or they will weaken.

- Mark all parts to ensure that they are refitted in their original positions on

assembly. If the valve collets have caused burrs on the valve stems, remove

them before removing the valves.

- Remove the seals (A) from the valve guides.

- Remember that seals must be replaced on assembly.

- Compress the springs using the valve spring compressor (1).

- Remove valve collets (2), spring retainer (3), springs (4), spring seat (5) and

remove the valve (6) from the opposite end.

Intake and exhaust valves are different, be careful not to confuse

them on assembly.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands