Husqvarna TC 250 2011 Page 59 Workshop Manual Download

Page: 59 / 366

D.29

SETTINGS AND ADJUSTMENTS

Ed. 07-2010

Changing handlebar position and height

Handlebar position (a) and height (b) can be modified to better suit your personal

preferences. To perform these adjustments, remove the handlebar clamp bolts

(3) and (4), and then remove the handlebar upper (1) and lower (2) clamps.

a) Changing handlebar position

Rotate the lower clamp by 180° to move handlebar position forward or back-

ward (10 mm - 0.04 in.).

b) Changing handlebar height

Remove the lower spacer (A) and replace the screw (4) with a 65 mm long

screw.

When finished, tighten the bolts (3) to 2.75-3.05 kgm (27 -30 Nm; 19.9-22 lb/ft)

and the bolts (4) to 2.0-2.2 kgm (19.6 -21.6 Nm; 14.5-15.9 lb/ft).

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands