Husqvarna TC 250 2011 Page 219 Workshop Manual Download

Page: 219 / 366

I.13

H02277

TC - TXCi

H02278

TC - TXCi

H02279

TC - TXCi

H02280

TC - TXCi

FRONT SUSPENSION

Ed. 07-2010

Fit the dust seal to the outer tube.

Make sure that there is not play between dust seal and outer tube.

Refit the cartridge.

Tighten the nut all the way onto the rebound adjuster rod.

Make sure rebound adjuster rod thread length is at least 15 mm (0.6 in.).

Fill the cartridge with the specified oil.

Pump the piston rod up and down repeatedly to remove any air from the cyl-

inder.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands