Husqvarna TC 250 2011 Page 260 Workshop Manual Download

Page: 260 / 366

L.8

H02297

BRAKES

Ed. 07-2010

Changing the fluid

Brake fluid should be checked and changed as per the "Maintenance Chart"

(see Section B), or earlier if contaminated with debris or water.

Do not change brake fluid in the rain or with a strong wind.

Use only fluid taken from a sealed container (DOT 4). Never reuse

brake fluid.

Avoid the ingress of contaminants such as dirt, water, etc. into the

reservoir.

Do not keep the reservoir open without its cover longer than neces-

sary; this would increase the risk of contamination.

Handle the fluid with care to avoid damage to painted parts.

Do not mix two brands of fluid. This would reduce boil-over point,

leading to loss of braking efficiency or degrading of rubber parts.

Replacement procedure is as follows:

- Take the rubber cap off the bleed valve (1) or (1A).

- Attach a clear plastic hose to the calliper bleed valve and place the other end

of the hose in a vessel.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands