Husqvarna TC 250 2011 Page 289 Workshop Manual Download

Page: 289 / 366

M.27

H02362

ELECTRICAL SYSTEM

Ed. 07-2010

Gear position sensor inspection (GPS: Gear Position Sensor)

Set the meter to the “Ohm” scale and disconnect the six-way connector (1) of the

alternator from the main wiring harness (the gear sensor wiring is secured to the

alternator wiring with a clip). Touch one meter probe to engine ground and insert

the other probe into the connector hole for the WHITE/BLACK gear sensor wire

(2). The lever (3) is placed on the left-hand side of the engine. After each gear

shift, it automatically returns to the horizontal position. First gear is engaged by

pushing the lever downwards; for other gears push it upwards. Check the read-

ings provided in the relevant table.

NEUTRAL (open circuit)

1st

556-568

2nd

817-833

3rd

1.48-1.51 K

4th

2.71-2.77 K

5th

6.75-6.88 K

TE - TXCi

NEUTRAL

312-319

1st

725-739

2nd

1,31-1,34

3rd

2.18-2.23 K

4th

3.61-3.68 K

5th

6.58-6.71 K

6th

15.2-15.5 K

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands