manualshive.com logo in svg

Husqvarna TC 250 2011, Workshop Manual, Page: 307 / 366

Share
Download
Husqvarna TC 250 2011 Workshop Manual Download Page 307

M.45

H00924

8

ELECTRICAL SYSTEM

Ed. 07-2010

•  Electronic control unit (5) and voltage regulator (6) position  

 (TE - TXCi).

Electronic control unit installed with the flat side down.

Voltage regulator installed over the electronic control unit.

Coat voltage regulator with heat grease.

• Securing the starter motor/solenoid starter cable (TE - TXCi)

Connect the starter motor/solenoid starter cable (7) as shown in the figure.

•  Securing the engine ground to chassis and engine ground to battery 

cables (8) (TE - TXCi)

The engine ground to chassis and engine ground to battery cables are secured 

to the timing chain tensioner screw.

•  Battery negative cable routing (TE - TXCi)

Routing of engine ground to battery negative cable (8).

Summary of Contents for TC 250 2011















































































































































































































































































































































































Reviews:

No comments