Husqvarna TC 250 2011 Page 261 Workshop Manual Download

Page: 261 / 366

L.9

H02298

BRAKES

Ed. 07-2010

- Remove the reservoir cap (2) or (2A) 21 mm wrench and the rubber gaiter.

- Loosen the bleed valve on the calliper.

- Pump the brake lever (3) or the brake pedal (3A) until draining all fluid.

- Tighten the bleed valve and fill the reservoir with fresh fluid.

- Loosen the bleed valve, operate lever or pedal, tighten the valve keeping

lever or pedal pressed and then release quickly.

- Repeat the process until the circuit is full and you can see clear fluid coming

out of the plastic hose: now tighten the bleed valve.

- Top up with fluid up to level (A) or (B) and refit rubber gaiter and reservoir

cover.

After changing the fluid, you will need to bleed air from the circuit.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands