Husqvarna TC 250 2011 Page 216 Workshop Manual Download

Page: 216 / 366

I.10

H02264

TC - TXCi

H02265

TC - TXCi

H02266

TC - TXCi

H02267

TC - TXCi

FRONT SUSPENSION

Ed. 07-2010

If outer tube and inner tube are still assembled together, place the fork leg upside

down and allow at least 20 minutes for oil to drain.

Remove the dust seal using a flat head screwdriver.

Remove the retaining ring using a flat head screwdriver.

Pull the inner tube until separating it from the outer tube.

Note: to facilitate removal, quickly (but carefully) pump the tubes back and forth

until separating them.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands