Husqvarna TC 250 2011 Page 221 Workshop Manual Download

Page: 221 / 366

I.15

H02285

TC - TXCi

H02286

TC - TXCi

H02287

TC - TXCi

H02288

TC - TXCi

FRONT SUSPENSION

Ed. 07-2010

Drain excess oil from the cartridge pushing the damper unit all the way home.

Be careful not to distort or damage the piston rod or any other parts.

Please note that excess oil may flow out from the hole located before the res

ervoir.

If you see no oil flowing out, it means that there isn't enough oil in the car

tridge.

Add oil to the cartridge before refitting it.

Drain excess oil from the reservoir.

Clean off any excess oil from the cartridge.

Install spring guide and spring on the cartridge.

Insert the cartridge into the inner tube.

Summary of Contents for TC 250 2011















































































































































































































































































































































































Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands

Husqvarna TC 250 2011, Workshop Manual

Search results

Summary of Contents for TC 250 2011

Reviews:

Related manuals for TC 250 2011

Brands by name

Popular brands