Husqvarna 2013 TC 250R Page 212 Workshop Manual Download

Page: 212 / 351

I.8

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H06813

H06818

H06819

H06820

FRONT SUSPENSION

Workshop Manual Ed. 07-2012

Loosen the cap nut at the top of each outer tube.

(Note: it is good practice to moderately slacken the cap nuts before removing

the fork legs from the motorcycle).

Drain oil from the damper unit.

Clamp the wheel axle carrier in a vice and loosen the adjuster screw.

Push down the inner tube.

Slip the tool shown in the figure between wheel axle carrier and cartridge nut.

Hold the nut with a wrench and remove the adjuster screw.

Be careful not to hurt your fingers.

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands

Husqvarna 2013 TC 250R, Workshop Manual

Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands