manualshive.com logo in svg

Husqvarna 2013 TC 250R, Workshop Manual, Page: 174 / 351

Share
Download
Husqvarna 2013 TC 250R Workshop Manual Download Page 174

H.26

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

ENGINE REASSEMBLY

Workshop Manual  Ed. 07-2012

Heat up the left crankcase bearing housings and install the crankcase. 

To join the crankcase halves, tap with a plastic hammer. 

Tighten the screws (15) using an 8 mm wrench (10 Nm, 1Kgm, 7.25 ft/lb). Make 

sure to fit the screws in the correct positions according the specified pattern (see 

Section F, paragraph "Crankcase disassembly").

Cover the upper section of the engine with a cloth, a sponge or the like to prevent 

screws or other parts from accidentally falling into the engine. 

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Reviews:

No comments