Husqvarna 2013 TC 250R Page 80 Workshop Manual Download

Page: 80 / 351

E.20

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H11112

H11113

H11109

H11110

GENERAL PROCEDURES

Workshop Manual Ed. 07-2012

Voltage regulator removal (TC)

- Remove the fuel tank as described in the relevant paragraph.

- Disconnect the connector (1).

- Loosen the two screws (2) and remove the voltage regulator (3).

Coil / Stick-Coil removal

- With an 8-mm wrench loosen the screws (2), then remove the floater needle

(1).

- Disconnect the connector (3) and remove the coil / Stick-Coil (4).

- During the reassembly, pay attention to the positioning of the gasket (5) with

respect to the plate (1).

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands

Husqvarna 2013 TC 250R, Workshop Manual

Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands