manualshive.com logo in svg

Husqvarna 2013 TC 250R, Workshop Manual, Page: 245 / 351

Share
Download
Husqvarna 2013 TC 250R Workshop Manual Download Page 245

L.5

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

BRAKES

Workshop Manual  Ed. 07-2012

Checking brake pads for wear / replacing the pads

Check brake pad wear.

Service limit ”A”  

-   3.8 mm (front and rear pads) 

If service limit is exceeded, always replace the pads in pairs.

Be careful that no brake fluid or any oil gets on brake pads or discs. Clean off 

with alcohol any fluid or oil that inadvertently gets on the pads or disc.

Replace the pads with new ones if they cannot be cleaned satisfactorily.

PADS REMOVAL

-  Remove clips (1).

-   Slide out pins (2).

-   Remove pads.

  

Do not work the brake lever or pedal while removing the pads.

PADS INSTALLATION

-   Install new brake pads.

-   Reassemble the two pins (2) and the clips (1).

The above procedure eliminates the need to bleed the braking system after 

replacing the pads. Simply operate the control lever several times until bringing 

the pistons back to their normal position.

  Drain some fluid from the reservoir when replacing the pads, or the 

pistons backing up into the cylinders might cause fluid to spill out 

of the reservoir.

FRONT

REAR

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Reviews:

No comments