Husqvarna 2013 TC 250R Page 293 Workshop Manual Download

Page: 293 / 351

M.43

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H10143

H10144

H10145

H10146

H11136

ELECTRICAL SYSTEM

Workshop Manual Ed. 07-2012

• Fuel pump connector position (TC)

Position the fuel pump connector (21) as shown.

• Securing the wiring (TC)

- Fasten the alternator cable to the clutch tube by means of the clamps (1).

- Fasten the condenser connector (2) to the support bracket by means of the

clamp (3).

- Fasten the harness to the chassis with the clips (4) as shown.

- Fasten the cables coming from the front part of the bike to the chassis by

means of the openable clamp (5).

- Fasten the front cables with a clamp (6).

• Securing the engine stop button cable (TC)

Secure the engine stop button cable (8) with two clips (9).

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands

Husqvarna 2013 TC 250R, Workshop Manual

Search results

Summary of Contents for 2013 TC 250R

Reviews:

Related manuals for 2013 TC 250R

Brands by name

Popular brands