manualshive.com logo in svg

Husqvarna 2013 TC 250R, Workshop Manual, Page: 78 / 351

Share
Download
Husqvarna 2013 TC 250R Workshop Manual Download Page 78

E.18

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H10021

1

2

H11106

4

3

GENERAL PROCEDURES

Workshop Manual  Ed. 07-2012

Start-up relay removal (TE-TXC)

-  Remove saddle and left-hand side panel (in this order) as outlined in the 

relevant paragraphs.

-  Disconnect the negative and positive cables of the battery.

-  Disconnect the starter motor positive cable (1) from the solenoid starter.

-  Disconnect the connector (2) and remove the solenoid starter (3) from its 

mount.

Condenser 

  This operation must be performed with a cool engine.

-  Cut the clamp (1) and disconnect the connector (2).

-  Pull outwards the condenser (3) so that it comes out of the supporting bracket 

(4).

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Reviews:

No comments