manualshive.com logo in svg

Husqvarna 2013 TC 250R, Workshop Manual, Page: 44 / 351

Share
Download
Husqvarna 2013 TC 250R Workshop Manual Download Page 44

D.14

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

SETTINGS AND ADJUSTMENTS

Workshop Manual  Ed. 07-2012

C: to increase clearance
D: to decrease clearance

Rear brake pedal free play adjustment

The rear brake pedal should have 5 mm free play (B) before the brake begins 

to bite. Should this not happen, operate as follows:

-  Loosen the nut (3);

-  Operate the master cylinder linkage (4) to increase or decrease free play;

-  Tighten the nut (3) at the end of the operation.

  When the free play requirement is not met, the brake pads will be 

subjected to an early wear that may lead to TOTAL BRAKE INEF-
FECTIVENESS.

  If the brake pedal feels mushy when pulled, there may be air in the 

brake line or the brake may be defective. CHECK THE BRAKING 
SYSTEM (see Section L).

Rear brake fluid level check  

Level (A) must be between the MIN and MAX notches visible on the master 

cylinder reservoir.

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Reviews:

No comments