manualshive.com logo in svg

Husqvarna 2013 TC 250R, Workshop Manual, Page: 291 / 351

Share
Download
Husqvarna 2013 TC 250R Workshop Manual Download Page 291

M.41

TE 250R - 310R 2013 I.E. / TE 310R 2013 I.E. USA

TC 250R 2013 - TC 250R 2013 I.E. USA

TXC 250R - 310R 2013 I.E. USA

H10135

1

H10136

3

H10137

1

2

3

H11428

2

ELECTRICAL SYSTEM

Workshop Manual  Ed. 07-2012

Cable routing and electrical parts installation instructions (TC)

•  Position of the coil / stick-coil

Connect the coil / stick-coil (1) as the figure shows.

•  Fuel injection control unit position (2) (TC)

Electronic control unit installed with the flat side up.

•  Position of the voltage regulator (3) (TC)

Positioned on the RH under the tank.

•  Position of the connectors front side

On the front side, under the fairing, the following connectors are to be found:

1)

  Mapping connector

2) 

 Diagnostic connector 

3)

  Connector not in use

Summary of Contents for 2013 TC 250R
































































































































































































































































































































































Reviews:

No comments