Huawei V100R021C00 User Manual Download Page 88

Page: 88 / 508

Indicator

Color

Name

Status

RUN

Green

Communication status

indicator

● Off: The power is

abnormal or the

board program is

● Blinking at long

intervals: The access

actuator

successfully registers

with the ECC800-

Pro and the

software runs

properly (the

indicator blinks at

0.5 Hz, on for 1s

and then off for 1s).

● Blinking at short

intervals: The

communication fails

or the access

actuator fails to

ECC800-Pro (the

indicator blinks at 4

Hz, on for 0.125s

and then off for

0.125s).

● Blinking: The

indicator blinks at

super short intervals

for 0.5s (blinking at

10 Hz, on for 0.05s

and then off for

0.05s) and then

turns off for 0.5s.

The cycle lasts for

5s.

ALM

Red

Alarm indicator

● Steady on: A system

failure alarm is

generated.

● Off: No system

alarm is generated.

FusionModule800 Smart Small Data Center

User Manual

3 System Architecture

Issue 01 (2021-02-05)

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands