manualshive.com logo in svg

Huawei V100R021C00, User Manual

Share
Download
Huawei V100R021C00 User Manual Download Page 203

Figure 4-137 Installing mounting ears

6. Install the IVS1800 in the cabinet.

1. Lift the device from both sides and carefully position it at the front of the

cabinet.
2. Lift the device slightly above the guide rails, gently place it on the guide

rails, and then slide it into the cabinet until the mounting ears of the subrack

contact the mounting bars at the front of the cabinet.

7. Thread M6 screws (prepared by the customer) through two slotted holes on

each mounting ear. Fasten the M6 screws using a Phillips screwdriver to fix

the mounting ears on the front mounting bars of the cabinet, as shown in the

lower right figure.

Figure 4-138 Securing the device

Step 3 Power on the device.

1. Turn on the power switch.
2. Check the indicators on the front panel of the device for its running status.

----End

4.2.9.8 Installing a Smart ETH Gateway and an ETH Converter

If a smart ETH gateway is configured, perform the following steps to install it.

Prerequisites

●

The smart ETH gateway (prepared by the customer), guide rails, screws, and

other installation accessories are available.

●

The number and installation positions of smart ETH gateways have been

determined.

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

191

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands