manualshive.com logo in svg

Huawei V100R021C00, User Manual

The Huawei V100R021C00 User Manual is available for free download from our website. This comprehensive manual provides detailed instructions and valuable insights on operating and maximizing the features of the Huawei V100R021C00. Obtain all the knowledge needed to make the most of your device with this essential user manual.

Share
Download
background image

Procedure

Step 1 Shut down the smart cooling product over the EMS.

●

Method 1: Log in to the ECC800-Pro mobile phone or pad app as user admin.
a. Choose Home.
b. Tap the cabinet that houses the smart cooling product in the micro-

module view.

c.

Tap the smart cooling product to be set in the cabinet layout diagram.

d. Choose Real-time Data > OFF.

●

Method 2: Log in to the ECC800-Pro WebUI as user admin. Choose

Monitoring > Cooling > NetCol5000-A1 > Controls > Control Information,

choose Startup/Shutdown control > OFF, and then click Submit.

NO TE

1 in NetCol5000-A1 is variable and subject to changes with the smart cooling product

connection sequence. The displayed value prevails.

Step 2 Disconnect the power supply from the smart cooling product control unit after the

smart cooling product shuts down over the EMS.

Step 3 Reclaim the refrigerant.
Step 4 Pry the EEV coil off using a flat-head screwdriver, as shown in 

Figure 6-21

.

Figure 6-21 Removing the EEV and coil

Step 5 Weld the two ends of the EEV using a welding torch, as shown in 

Figure 6-21

.

Then, remove the EEV.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

428

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V100R021C00

RAUMEDIC MPR1 Instructions Manual preview
MPR1
Brand: RAUMEDIC Pages: 98
G-Tek LM Pro 63 Series Operating Manual preview
LM Pro 63 Series
Brand: G-Tek Pages: 40
G-Tek LM Pro T Operating Manual preview
LM Pro T
Brand: G-Tek Pages: 25
Watlow D4T User Manual preview
D4T
Brand: Watlow Pages: 214
Elitech RCW-360 User Manual preview
RCW-360
Brand: Elitech Pages: 2
Grosvenor GT10S Installation Manual preview
GT10S
Brand: Grosvenor Pages: 2
Edaphic Scientific ESCM-191 User Manual preview
ESCM-191
Brand: Edaphic Scientific Pages: 19
EchoStar Hughes 4200 User Manual preview
Hughes 4200
Brand: EchoStar Pages: 58
UEi Apollo IV DT304 Instruction Manual preview
Apollo IV DT304
Brand: UEi Pages: 20
red lion Data Station Plus Manual preview
Data Station Plus
Brand: red lion Pages: 8
MadgeTech PR2009 Product User Manual preview
PR2009
Brand: MadgeTech Pages: 12
FCS Multilog2 Installation And Setup preview
Multilog2
Brand: FCS Pages: 44
Emerson GO USB Humidity User Manual preview
GO USB Humidity
Brand: Emerson Pages: 18
V-Sun BTGP-38KM User Manual preview
BTGP-38KM
Brand: V-Sun Pages: 8
EESiFlo 6000 Series Setup Manual preview
6000 Series
Brand: EESiFlo Pages: 2
Meteo Control blue'Log X Series Operating Manual preview
blue'Log X Series
Brand: Meteo Control Pages: 56
Orolia VersaSync Getting Started Manual preview
VersaSync
Brand: Orolia Pages: 35
TESTO 175-H2 Manual preview
175-H2
Brand: TESTO Pages: 2

Brands by name

Popular brands

Load more brands