manualshive.com logo in svg

Huawei V100R021C00, User Manual

Share
Download
Huawei V100R021C00 User Manual Download Page 190

Figure 4-114 Cable connections to T/H sensors

(1) ECC800-Pro

(2) T/H sensor 2

(3) T/H sensor 1

(4) Temperature sensor

----End

4.2.9.4.3 (Optional) Installing Temperature Sensors

Procedure

Step 1 Bind the temperature sensors to the right posts of the front and rear doors about

1.6 m above the floor using cable ties.

NO TE

● When installing a temperature sensor, bind the cable behind the sensor to the cabinet and

keep them 20 mm away from the sensor probe.

● Temperature sensors must not be in touch with metal parts or cabinets.
● Ensure that the temperature sensor on the rear door of the cabinet is installed on the side

without a PDU2000.

● Verify that the temperature sensors face the inside of the cabinet to ensure accurate

measurement of cabinet interior temperatures.

● Install other temperature sensors based on the layout.

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

178

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands