Huawei V100R021C00 User Manual Download Page 31

Page: 31 / 508

2.3 Typical Application Scenarios

The smart module mainly applies to government, education, medical care,

transportation, energy, finance, small- and medium-sized enterprises, and

branches of large companies.

Target markets:
●

Asia Pacific, Africa (including high-temperature areas in North Africa), Europe,

and Middle East (380–415 V, 3Ph+N, 50/60 Hz power systems are supported.)

FusionModule800 Smart Small Data Center

User Manual

2 Product Description

Issue 01 (2021-02-05)

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands