Huawei V100R021C00 User Manual Download

Page: 497 / 508

Step 5 Secure the fingerprint and card reader to the bottom plate.

Step 6 Configure the new fingerprint and card reader by following the instructions

provided in the document delivered with it.

Step 7 Choose Monitoring > System > ECC800-Pro > Controls and delete the device

failing in communication.

Step 8 Refer to the section about commissioning the in-room access control system in the

installation guide and check that the fingerprint and card reader with a keypad

functions properly.

----End

Follow-up Procedure

Configure the new fingerprint and card reader by following the instructions

provided in the document delivered with the ECC800-Pro.

6.4.4.22 Replacing a Card Reader with a Keypad

Prerequisites

●

Recommended tool: Phillips screwdriver

●

A card reader with a keypad needs to be replaced.

●

A spare card reader with a keypad of the same model is available and

functional.

Context

Figure 6-79 Card reader with a keypad

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

485

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands