Huawei V100R021C00 User Manual Download Page 255

Page: 255 / 508

Context

Figure 4-215 Description of ports on the access actuator

(1) 48 V power port

(2) PoE port

(3) RS485 port (COM2)

(4) RS485 port (COM1)

(5) Address DIP switch

(6) Status indicator

(7) BLINK button

(8) WG_2 Wiegand

interface

(9) WG_1 Wiegand

interface

(10) AI/DI_2 dry contact

(11) AI/DI_1 dry contact

(12) LOCK/GND/

GATE/COM/door status

sensor and magnetic lock

port

Procedure

Step 1 Remove the covers from the waterproof box and cable holes of the access

actuator.

Step 2 Connect cables by referring to

Figure 4-216

1. Connect the smart ETH gateway to the access actuator using a cable.
2. Connect the single/double door magnetic lock to the access actuator using a

cable.

3. Connect the access controller to the access actuator using a cable.
4. Connect the exit button to the access actuator using a cable.

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

243

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands