Huawei V100R021C00 User Manual Download Page 383

Page: 383 / 508

Cat

ory

Sympt

Possible Cause

Measure

The water inlet pipe

or drainpipe leaks.

Check the water inlet pipe and

drainpipe and their connectors, and

repair or replace them based on site

requirements.

Humidi

ty is

high or

there is

conden

sation

in the

equipm

ent

room.

For a single smart

cooling product, the

server heat load is

lower than 2.5 kW.

● Verify that the doors, windows,

floors, and ceilings of the equipment

room are properly sealed.

● If the outdoor humidity is too high,

shut down the fresh air system.

● Open the aisle doors or control

skylights of the data center, or open

the filler panels of some server

cabinets.

Use the cold aisle containment to

control the humidity.

Add extra dehumidifiers.

tdo

uni

Abnor

mal

noise is

generat

during

operati

on.

The compressor, fan,

or pipes are loose.

Check and secure loose parts.

The

compre

ssor

does

not

work.

The high and low

pressure switches are

triggered.

Check the high and low pressure

switches.

The circuit breaker,

fuse, or cable is

disconnected.

Check the main circuit breaker, fuses,

and cables.

The compressor

motor is damaged.

Check whether the motor is damaged.

Replace the motor if it is faulty.

The compressor does

not need to start.

Check for the requirement status on the

LCD.

The compressor does

not work.

Check whether the compressor driver is

faulty. Replace the compressor driver if

it is faulty.

The

compre

ssor

dischar

The refrigerant loop

or component is

blocked.

Clean the loop and components.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

371

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands