manualshive.com logo in svg

Huawei V100R021C00, User Manual

Share
Download
Huawei V100R021C00 User Manual Download Page 37

Cabinet Door

●

In cold and hot aisle containment, a sealed glass door is configured at the

front and a sealed sheet metal door at the rear.

●

By default, the front and rear doors of a cabinet are equipped with electronic

clasp locks, which can be unlocked only by using dedicated keys.

Figure 3-7 Front door

Figure 3-8 Rear door

Cable Trough (Optional)

●

Cable troughs are clamped one by one to form a whole. A cable trough is

assembled by clamping two side panels, one pallet, and one baffle (used to

separate ELV optical fiber cables from ELV network cables and electrical route

A from electrical route B).

FusionModule800 Smart Small Data Center

User Manual

3 System Architecture

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

25

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands