Huawei V100R021C00 User Manual Download Page 116

Page: 116 / 508

Figure 4-11 Installing ramps

4. Raise the six leveling feet to the highest point using an adjustable wrench,

and push the cabinet to the installation position over castors. (Optional)

----End

4.2.1.2 Smart Cooling Product Transportation and Unpacking

Checking the Outdoor Unit Upon Arrival

Step 1 After the outdoor unit is delivered onsite, check the overtemperature mark.

Overtemperature marks are attached to the outer package and indicate whether

the ambient temperature during transportation exceeds the threshold. If yes, the

corresponding temperature mark background turns black, as shown in

Figure

4-12

Figure 4-12 Overtemperature mark

●

If none of the three marks turn black, the transportation meets requirements

and the outdoor unit can be installed after its package is removed as

instructed in

Unpacking the Outdoor Unit

●

If the mark with 60 turns black, unpack the outdoor unit and open its top

cover, front panel, and left front panel. Then check whether there is trace of

liquid around the safety valve connector. If yes, replace the safety valve. If no,

install the outdoor unit. For position of safety valve, see the overtemperature

mark.

●

If the marks with 60, 65 turn black or all the marks turn black, ask Huawei to

confirm whether the unit can be used.

----End

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

104

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Brands by name

Popular brands