manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 98

vlan

 

vlan-id

An RSPAN VLAN is created and the RSPAN VLAN view is displayed.

3.

Run:

mac-address learning disable

The MAC address learning is disabled.

NOTE

If MAC address learning is disabled in the VLAN, other services cannot be configured in the VLAN.

4.

Run:

quit

Return to the system view.

5.

Run:

observe-port

 

index

 

interface

 

interface-type

 

interface-number

 [ 

vlan

 

vlan-

id

 ]

An observing port is configured, and the RSPAN VLAN is specified.

6.

Run:

traffic behavior

 

behavior-name

A traffic behavior is created and the traffic behavior view is displayed.

7.

Run:

mirroring

 

to observe-port

 

index

Remote flow mirroring is configured.

After configuring flow mirroring in a traffic behavior, you need to bind the behavior
to a traffic classifier in a traffic policy and then apply the policy to the interface. For
details, see 

7.11.4 Creating and Applying a Traffic Policy

.

l

Configure the RSPAN VLAN on the intermediate switch and add interfaces to the RSPAN
VLAN.

The configuration is the same as that for remote port mirroring. For details, see 

7.3.2

Configuring Remote Port Mirroring

.

l

Configure the remote observing Interface on the destination switch.

The configuration is the same as that for remote port mirroring. For details, see 

7.3.2

Configuring Remote Port Mirroring

.

----End

7.12.4 Creating and Applying a Traffic Policy

Context

For how to configure traffic classification rules on the source S5700, see 

7.11.4 Creating and

Applying a Traffic Policy

.

7.12.5 Checking the Configuration

Run the following commands to check the previous configuration.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

89

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands