manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 92

An RSPAN VLAN is created and the RSPAN VLAN view is displayed.

3.

Run:

mac-address learning disable

The MAC address learning is disabled.

NOTE

If MAC address learning is disabled in the VLAN, other services cannot be configured in the VLAN.

4.

Run:

quit

Return to the system view.

5.

Run:

observe-port

 

index

 

interface

 

interface-type interface-number

 [ 

vlan

 

vlan-

id

 ]

An observing port is configured, and the RSPAN VLAN is specified.

6.

Run:

vlan

 

vlan-id

The view of the VLAN that the observed MAC address belongs to is displayed.

7.

Run:

mac-mirroring

 

mac-address

 

to

 

observe-port

 

index

 

inbound

Remote MAC address mirroring is configured and the RSPAN VLAN is specified.

To observe incoming packets from or destined for multiple MAC addresses, repeat

Step 6

 and 

Step 7

.

l

Configure the RSPAN VLAN on the intermediate switch and add interfaces to the RSPAN
VLAN.

The configuration is the same as that for remote port mirroring. For details, see 

7.3.2

Configuring Remote Port Mirroring

.

l

Configure the remote observing port on the destination switch.

The configuration is the same as that for remote port mirroring. For details, see 

7.3.2

Configuring Remote Port Mirroring

.

----End

7.9.3 Checking the Configuration

Run the following commands to check the previous configuration.

Action

Command

Check information about the
observing port.

display observe-port

Check information about MAC
address mirroring.

display port-mirroring

 

If the following results are obtained, the configuration is successful:

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

83

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands