manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 50

You can run the 

display elabel

 command to check information about the hardware code. The

hardware code provides necessary basis for such services as network installation, network
upgrade, network expansion, device management and maintenance, and device replacement in
batches.

The displayed information includes: type of the card, bar code, Bill of Material (BOM) code,
English description, production date, supplier name, issuing number, Common Language
Equipment Identification (CLEI) code, and sales BOM code.

Procedure

Step 1

Run:

display elabel

 [ 

slot

 

slot-id

 [ 

subcard-id

 ] ]

The electronic labels are displayed.

----End

4.2.4 Checking Temperature

Context

You can run the following command in any view to check the working temperature of the
S5700.

Procedure

Step 1

Run:

display environment

 [ 

slot

 

slot-id

 ]

The temperature of a temperature-sending SIC is displayed.

----End

4.2.5 Checking the Fan Status

When the device temperature is high, you can check whether the fan is functioning normally.

Procedure

Step 1

Run:

display fan

 [ 

slot

 

slot-id

 | 

verbose

 ]

The fan status is displayed.

----End

4.2.6 Checking the Power Supply Status

Before replacing a power supply, you need to check the status of the power supply.

Procedure

Step 1

Run the following command in any view:

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

4 Using display commands to check the status of the device

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

41

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands